Long screw damage can be caused on many different devices such as the iPhone 5S, iPhone SE, iPhone 6/6S and 7 series. Each model has different locations for possible long screw damage. Depending on the model of the iPhone long screw damage can range in severity from "basic" problems such as no backlight, no service or much bigger problems such as no image, or no boot caused by a 1v8 short.
Read MoreA flexible printed circuit (FPC) connector is used to connect to circuits together in a device or unit that flexes in a small or confined manner that does not otherwise allow a socketed connection. Often times these connectors are made from a brittle plastic that is not rated for many connects and disconnects, as such they can fail with normal installations. This service is to repair or replace a damaged FPC connector on any device.
Read MoreIn order to determine if the Tristar IC is functioning properly, test the voltage of the battery terminal--after you confirm that the phone is pulling amps using the ammeter
Read MoreThe best thing to do when getting your phone and/or laptop wet is to resist the urge to turn it on. Don't charge it or plug it into anything. Let it dry out and bring it into our repair shop asap. Most commonly people think that rice will save a wet phone, which is a mis-nomer. The real cause is shorts and corrision, rice will never clean corrison.
Read MoreTypically we see iPhone 6 Plus and iPhone 6S Plus with a half backlight due to the phone needing not one but two anode backlight circuits. With one anode backlight gone out it effectively shuts off half of the led light strip in the backlight panel.
Read MoreThe most common use of the micro coax connector is using 2 or more anchor-points which are typically grounded in the circuit then a center pin also known as the "hot wire" is what carries the signal and is mounted to a center point and runs either to other points on the board and/or through a via to connect to another layer.
Read MoreOne problem known to the Sony Z3V owners is that the micro usb port is often times subject to failure after being plugged in and unplugged many times over the life of the device.
Read MoreWith the aide of schematics, board views and donor parts these repairs are often feasible and much cheaper then the alternative which would involve replacing the whole motherboard, which sometimes can compromise the data on the device, rendering the information unreadable.
Read MoreThis is a common problem of Samsung tablets, the battery connector is prone to cracking causing the flickering screen, random shutdown/restart, quick discharge, battery capacity fluctuation.
Read MoreOften times the boot looping issue on the LG Nexus 5 is caused by a failing power button which needs to be removed and then replaced with a new one which involves using a hot air station as well as micro soldering techniques.
Read MoreWhen working on cell phones for data recovery getting the phone fully functional is not needed. Often times from liquid damage issues such as not charging or no backlight will be present.
Read MoreThis issue is normally caused by using cheaper third party charger that does not regulate the voltage and as such spikes in the voltage will ruin the charging integrated circuit.
Read MoreThe most common DIY mistake when replacing a battery is prying up on the board-side and breaking the connection of many small capacitors and inductors which are needed for the phone to boot properly. The repair invovles replacing the missing components to allow the phone to charge and boot as required.
Read MoreTypically for a backlight to go out on the iPhone 6S would be a result of a few things, 1 being liquid damage on the motherboard causing corrosion and shorting out the backlight circuit which contains a diode, a backlight ic (U4020) as well as few other discrete components. Another way a backlight circuit can go out is also by installing a replacement screen and bridging a few of the connectors on the LCD FPC connection thus causing a short and ruining the circuit.
Read MoreA blown back light on an iPhone 6 is typically caused by a screen replacement gone wrong or a sudden drop on the phone which can damage some of the components on the backlight circuit.
Lets take a look at the back light circuit and evaluate the possible issues and solutions to this problem.
Read MoreThis type of repair is common after the many months and years of plugging and unplugging the micro usb cable to charge. The physical usage this port sees with often contribute to the degradation of the port.
Read MoreOften times with smaller mobile devices, a need for shrinking the surface mounted components arises. With the smaller components comes smaller tools. Typically working with components on the 0402 scale and even smaller makes using standard tools very difficult. The scale is literally microscopic; components on a board can be smaller than a grain of rice (hence the microscope)
Read MoreRepairing an iPad Mini Digitizer and realized the pins had come out of the digitizer fpc connector? No need to worry! This a typical problem faced during ipad mini repairs and here at micro soldering repairs we love this repair!
In order to repair this we will remove and re-install a new digitizer fpc connector.
Read More
